CGI Sliding Glass & Patio Doors Nationwide | TruePane Windows & Doors

CGI Sliding Glass & Patio Doors in Palm Beach Gardens: What to Know First

We repair and replace CGI sliding glass and patio doors throughout Palm Beach Gardens as an independent CGI service provider. Most repairs on CGI sliders and patio doors take one visit, and we carry or can source the parts that fit CGI’s hurricane-rated frames correctly. You’ll get a written line-item quote before any work starts, no surprises on the bill.

Call (772) 794-8169

This page is for homeowners who already own CGI sliding glass or patio doors and need them to open, close, seal, and lock the way they did when they were new. If you have a CGI slider that binds, a patio door that leaks air, or rollers that sound like gravel, call us at (772) 794-8169. A live person answers, day or night.

Key Takeaways

• We service all CGI sliding glass and patio door lines installed in Palm Beach Gardens homes, including Estate, Targa, and Sentinel series.
• CGI doors use heavy-gauge aluminum frames, and that weight means roller and track wear shows up differently than on lighter doors.
• We are an independent service provider, not a CGI authorized dealer. That means we fix what’s failing without steering you toward a replacement unless replacement is actually the right call.
• Every repair carries our Done Right Promise: if it’s not right, we fix it. No paperwork fights.

How CGI Products Fail - and How We Fix Them

• Estate Series sliders: roller fatigue from salt-weighted air. Palm Beach Gardens sits close enough to the coast that salt and humidity work their way into wheel bearings faster than inland homes ever see. On Estate Series sliders, the original nylon rollers wear flat on one side, and the door drops a fraction of an inch. The door still opens, but it drags. We replace the rollers with sealed stainless-bearing units sized for the heavier Estate panel and true the track while we’re there. The difference is immediate: one hand opens it again.
• Targa Series patio doors: strike plate drift after years of daily use. Targa doors are common in mid-2000s Palm Beach Gardens builds, and the multi-point lock is a good design. But the strike plate on the jamb is held by screws into aluminum, and after a decade of South Florida afternoon storms, those screws can work loose enough that the top pins don’t fully seat. Homeowners feel the handle turn all the way but the door doesn’t seal tight at the top corner. We re-seat the strike plate, replace hardware where the threads are stripped, and re-shim the jamb so the pins seat full depth. It’s a small fix that stops a big air leak.
• Sentinel Series: gasket compression loss along the interlock. CGI’s Sentinel line uses a heavy overlapping interlock between the stationary and sliding panels. The weatherstrip in that interlock is the first thing to flatten in Florida heat. You’ll feel a warm draft at the center seam even when the door is locked. We replace the interlock gasket with the correct profile and durometer for Sentinel’s extrusion. Aftermarket universal weatherstrip does not fill the gap, and we’ve seen doors where someone glued in foam that peeled off within six months. We don’t do that.
• Sliding panel glass unit fogging on any CGI line. CGI doors use impact-rated laminated glass. When the seal fails and moisture gets between the panes, you cannot just replace the insulated glass unit with a cheap one from a supply house. The replacement unit has to match the impact rating for the opening, or you’ve downgraded a hurricane door into something that would fail inspection. We source CGI-spec glazing or equivalent impact-rated units and handle the glass swap without pulling the whole panel when the frame is sound.
• Bottom track corrosion at the drain weep holes. On some older CGI sliders in Palm Beach Gardens, the weep holes that let water drain out of the track get clogged with sand and landscape debris. Water sits in the track, aluminum pits, and eventually the track grooves catch the rollers. The fix is cleaning and de-scaling the track, verifying drains are clear, and re-coating where the anodizing has worn. If the track is too far gone, we can replace the track section rather than the entire door. That saves thousands on some jobs.

Our CGI Sliding Glass & Patio Doors Process

1. 1
   You call, and a person picks up. No menu tree. You describe the symptom, and we schedule a visit.
2. 2
   We measure and diagnose on site. Our technician inspects rollers, track, locks, strike plates, gaskets, and the glass unit. We measure twice.
3. 3
   You get a written line-item quote. We show you OEM CGI parts pricing next to quality aftermarket options where a safe alternative exists. For impact-rated glass, there is no aftermarket shortcut, and we’ll tell you that plainly.
4. 4
   We do the work, usually same visit. Most roller replacements, gasket swaps, strike plate repairs, and track tune-ups finish the same day. Glass lead time depends on the unit, and we give you a real date, not a guess.
5. 5
   We test the door in front of you. Open, close, lock, seal check at the interlock and jamb. If it does not pass, we do not leave.
6. 6
   You get the Done Right Promise in writing. If something we touched fails within 90 days, we return and make it right. No arguing.

What CGI Sliding Glass & Patio Doors Costs in Palm Beach Gardens

Here’s what CGI work in Palm Beach Gardens typically runs:

• Roller replacement (labor and parts): $180 to $420 per door, depending on model and roller type
• Track cleaning, de-scaling, and adjustment: $120 to $250
• Strike plate re-seat and hardware replacement: $140 to $310
• Interlock or perimeter gasket replacement: $180 to $520 depending on linear feet and profile
• Impact glass unit replacement (labor and glass): $900 to $2,800 depending on size and whether the panel must be removed and re-glazed
• Full CGI slider replacement (installed): $3,800 to $8,500 depending on size, configuration, and finish

What moves the price: door size, which CGI series you own, whether parts are OEM or acceptable aftermarket, and whether the frame itself is corroded or just the hardware. Call (772) 794-8169 for an exact quote on your door. The estimate is free, in writing, and the number on the quote is the number you pay.

Why Palm Beach Gardens Homeowners Call TruePane Windows & Doors for CGI Work

We’ve been serving this area since 2008, and Dale Kessler, our owner, grew up off Northlake Boulevard when Palm Beach Gardens was still a working town first. We know CGI doors because we’ve worked on hundreds of them across the Gardens, Jupiter, and the northern Palm Beaches. But we’re not a one-brand shop. We also service PGT, CWS, ES Windows, and ECO Window Systems, which matters when you have a home with mixed brands or a budget that calls for a straight comparison. Every recommendation we make for your CGI door is made without a manufacturer’s sales target attached. We fix what can be fixed and replace what cannot. We show up when we say, in uniform, background-checked, and we register both warranty layers in writing before the truck leaves your driveway. That’s The Keystone Standard, and it’s how every job ends: with a door that is true.

FAQs