ES Windows Custom & Geometric Windows Nationwide | TruePane Windows & Doors

ES Windows Custom & Geometric Windows in Palm Beach Gardens: What to Know First

We install, repair, and replace ES Windows custom and geometric units throughout Palm Beach Gardens, and most jobs are finished in one visit. A typical custom ES Windows repair here runs between $280 and $1,900 depending on the glass, the shape, and whether the frame or the seal gave out first. We are an independent ES Windows service provider, which means we order the right parts rather than push whatever is on the truck. If you own an ES Windows arched transom, a clipped-corner trapezoid, or an oversized radius unit that has started to fog, bind, or leak, you are on the the right page. Call (772) 794-8169 and a person answers.

Call (772) 794-8169

This page is for you if:

• You own ES Windows custom or geometric windows and the original installer no longer answers the phone.
• You have a shaped unit that is fogged, cracked, or letting water into the frame after a Palm Beach County storm.
• You need a like-for-like replacement that keeps the original look on a home you plan to stay in.

How ES Windows Products Fail - and How We Fix Them

ES Windows are built for South Florida’s wind loads and coastal exposure, but custom and geometric shapes push every manufacturer’s engineering past what standard rectangular units endure. Shaped glass does not flex the way a square lite does. Corners concentrate stress. Curves concentrate it further. Here is what we see on ES Windows jobs in Palm Beach Gardens, model by model.

• The ES Targa and ES Elite lines: corner seal separation on trapezoids and clipped-corner units. On ES Targa series trapezoids, the sealant bond at the tightest angle is under constant tension from the weight of the glass above it. After ten or more years of Palm Beach Gardens heat cycling, that corner is where the insulating gas escapes first. We remove the sash, inspect the spacer, and re-seal with manufacturer-spec materials, not a tube of clear silicone from the hardware store. If the seal has already blown, we replace the insulated glass unit and reset the corner glazing with the proper bedding tape.
• The ES Windows architectural radius line: stress cracks at the apex of arched transoms. Arched glass carries its own weight along the curve. The apex of an ES radius transom is where we find hairline stress fractures that start small and spread after the first good windstorm. We identify the crack type before touching anything, because a stress crack means the glass was cut or set slightly off dimension. The fix is a new lite templated from the actual opening, not the original order sheet, which is usually off by a sixteenth of an inch.
• The ES Windows casement and picture frame in custom trapezoid configurations: roller drag and warped sash. On custom ES picture and casement units, the aluminum frame can twist under a shaped glass load, which causes the sash to drag against the sill. We re-shim and re-square the frame to the rough opening, then reset the glass. This is the difference between a unit that opens with two fingers and one that requires shoulder weight after a year.
• The ES Impact Series with custom shapes: water weep failure along the bottom track. ES Windows’ impact-rated units rely on small weep holes along the bottom track to shed water. In Palm Beach Gardens, pollen, sand, and salt spray clog those weeps within a few years. On shaped units where the bottom track is curved, the weep placement is less forgiving. A clogged weep forces water over the interior dam and into the wall cavity. We clean, enlarge, and reposition weeps where the design allows, then test with a running hose before we call the job done.
• The ES Windows sliding glass door with a geometric transom above: header deflection cracking the transom seal. When an oversized ES slider carries a geometric transom, the header does real work. If the original installer undersized the header or failed to flash it, the transom shifts and the seal fails. We check the header deflection with a laser before we touch the glass. If the framing needs correction, we say so in writing before any glass is ordered. We do not glue up a failing transom and walk away.

Our ES Windows Custom & Geometric Windows Process

We follow the same order of operations on every ES Windows job in Palm Beach Gardens, whether it is a repair or a full custom replacement.

1. 1
   Measure the opening twice. We measure the actual rough opening and the existing unit. For shaped glass, we template the curve or angle directly off the frame, not off paperwork. A custom ES Windows unit is only as good as the template.
2. 2
   Diagnose the failure in writing. We put the problem on paper: failed seal, cracked lite, bent hinge, warped frame, water intrusion path. You see it before any work is authorized.
3. 3
   Source the right parts. We order ES Windows OEM glass and hardware where it is still available. Where ES Windows has discontinued a custom shape or series, we have aftermarket fabricators we trust who cut to the same spec. We tell you which we are using and why before we order.
4. 4
   Do the work clean. The technician arrives in uniform, lays down floor protection, and works the way we would in our own mother’s house. The old unit comes out without damaging the surround. The new or repaired unit goes in square, shimmed, and sealed.
5. 5
   Test and document. We run the window through its full travel, check the seal with a moisture meter, and water-test any exterior-facing unit. When it passes, we register the manufacturer warranty in writing and hand you the paperwork before the truck leaves the driveway.
6. 6
   Stand behind it. If anything is not done right, we make it right within 90 days. No paperwork fight, no arguing.

What ES Windows Custom & Geometric Windows Cost in Palm Beach Gardens

Here are straight ranges for the ES Windows custom and geometric work we do most often in this market. They are line-item ranges, not wishful numbers.

• Custom trapezoid or clipped-corner sash re-seal (ES Targa or Elite): $280-$520 per sash, depending on glass size and whether the sash needs re-glazing.
• Sealed-unit replacement on a geometric ES window (fogged or failed): $480-$1,200 per unit, depending on the lite dimensions and whether the sash is reusable.
• Complete custom ES Windows replacement with new insulated low-E glass and frame reset: $1,400-$3,600 per opening for an average home. Oversized or curved units run higher.
• Radius or arched ES transom replacement templated from the actual opening: $900-$2,100 depending on curve radius and glass spec.
• Geometric transom above an ES slider, including seal replacement and re-flashing: $750-$1,800.

What moves the price: glass type (impact-rated costs more than non-impact), shape complexity (a radius costs more than a clip corner), frame condition, and access. A second-story radius unit on a zero-lot-line home in Palm Beach Gardens costs more to work on than a first-floor trapezoid. Call (772) 794-8169 for a written, line-item estimate. The estimate is free, and the price does not change once we start.

Why Palm Beach Gardens Homeowners Call TruePane Windows & Doors for ES Windows Work

Dale Kessler grew up off Northlake Boulevard, close enough to the old groves that he still thinks of Palm Beach Gardens as a working town first and a resort town second. Our guys know what ES Windows units in this city actually go through: salt spray, afternoon storms, and summers that test every seal on the house. We are an authorized installer for more than a dozen manufacturer lines, including PGT, CGI, CWS, and ECO Window Systems, which means if your ES Windows unit is not worth saving we can show you side-by-side options on paper. Every job carries the Done Right Promise and the Keystone Standard: both manufacturer warranty layers registered in writing, durations stated, before the truck leaves the driveway. A live person answers the phone 24 hours a day. If the pane is not true, the job is not done.

FAQs